Administrator
|
It is good to have guys looking out for you, and you guys do a good job of that for me. A few days ago I got a text from Kyle saying "Look at this!". I did, and quickly consulted the catalog - a NOS non-step rear bumper for Dad's truck. A bit of to & fro with Kyle determined that a non-step bumper would look a lot better on a "sport truck" than the nice step bumper I got from Jerry/Ozark1 - which can now go to Big Blue.
Thanks, Kyle! (For the curious photographers, both of those were shot with this iPad, and were in portrait instead of landscape mode. Both were edited with Photoshop Express, and the first one was actually rotated in the "crop" function. But the second one was cropped only slightly, but just enough to be require saving, and just saving it also rotated it. Oh, and I added width="100%" to the code so they take up whatever screen with the user has.)
Gary, AKA "Gary fellow": Profile
Dad's: '81 F150 Ranger XLT 4x4: Down for restomod: Full-roller "stroked 351M" w/Trick Flow heads & intake, EEC-V SEFI/E4OD/3.50 gears w/Kevlar clutches
|
Administrator
|
What a find Gary! I've seen that bumper quite a bit in the junkyards but always attached to a Bronco. That is a beautiful piece!
SHORT BED 4-DOOR DIESEL: 1986 F350 4x4 under construction-- 7.3 IDIT ZF5+GVOD
STRAIGHT SIX 4X4: 1981 F150 2wd to 4x4-- 300 I6 close ratio diesel T19, hydroboost brakes, Saginaw steering BIG F: 1995 F-Superduty under construction— converting to 6.9L IDI diesel ZF5+DNE2 |
Administrator
|
Kyle said it was only on eBay 30 minutes before I bought it. And in that time he got a suggestion from eBay, sent me a text, I looked at the eBay post, looked the part up in the catalog, chatted with Kyle about it, talked to my wife about it, and pulled the trigger.
And it is a beautiful piece. Now I need to find a NOS front bumper and maybe one of the grille pieces of trim. I really do need to figure that out and document what I have. But I know I have all NOS side trim, grille, badges, windshield trim, and now rear bumper. I think I have the headlight doors NOS, and either the upper or lower grille trim. I gotta go see and write it down.
Gary, AKA "Gary fellow": Profile
Dad's: '81 F150 Ranger XLT 4x4: Down for restomod: Full-roller "stroked 351M" w/Trick Flow heads & intake, EEC-V SEFI/E4OD/3.50 gears w/Kevlar clutches
|
Digging up an old thread. Anyone have any photos of this on a truck vs a Bronco?
1986 F-150 SC 2wd 4spd 302EFI Base Model all OEM motor/trans/emissions equipment.
|
Administrator
|
In reply to this post by Gary Lewis
https://www.ebay.com/itm/Nos-1980-1996-Ford-Truck-Front-Bumper-E0TZ-17757-A/123326740773?epid=19022956013&hash=item1cb6d8b925:g:luUAAOSwrORbfbgU I believe it is the bottom one you are seeking, Gary? |
In reply to this post by fords4life
Found a couple photos online and found a couple of aftermarket versions for $200ish vs nearly $500 for an NOS version. Think I'm going to go this route on my rig.
Gary - Do you have the part numbers sheets for the brackets for this style of bumper? I see the illustrations, but it looks like the part numbers are only posted for the actual bumpers. Thanks all!
1986 F-150 SC 2wd 4spd 302EFI Base Model all OEM motor/trans/emissions equipment.
|
Administrator
|
fords4life - Unless I don't understand what bumper you are talking about, the front bumper bolts directly to the frame. So, what am I missing?
David - That bumper requires the rubber pad. But Dad's truck doesn't have them. Just the chrome bumper. But thanks anyway.
Gary, AKA "Gary fellow": Profile
Dad's: '81 F150 Ranger XLT 4x4: Down for restomod: Full-roller "stroked 351M" w/Trick Flow heads & intake, EEC-V SEFI/E4OD/3.50 gears w/Kevlar clutches
|
Sorry Gary, I was taking about the rear bumper on your original post.
Nathan
1986 F-150 SC 2wd 4spd 302EFI Base Model all OEM motor/trans/emissions equipment.
|
Administrator
|
Nathan - See if this answers the questions: Exterior/Bumpers.
Gary, AKA "Gary fellow": Profile
Dad's: '81 F150 Ranger XLT 4x4: Down for restomod: Full-roller "stroked 351M" w/Trick Flow heads & intake, EEC-V SEFI/E4OD/3.50 gears w/Kevlar clutches
|
Edit this page |